CAN I INSTALL A BATH TUB MYSELF? CONSIDERATIONS AND ACTIONS

Can I Install a Bath Tub Myself? Considerations And Actions

Can I Install a Bath Tub Myself? Considerations And Actions

Blog Article

Estimating

The content down below pertaining to A Step-by-Step Guide to Installing a Bathtub is definitely compelling. Try it and make your own assumptions.


How to Install a Bathtub
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is readily obtainable, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the task and are comfortable trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you might require a professional plumber to make tube connections.
This article will certainly help you mount a new bath tub in your restroom if you have actually already gotten a brand-new tub and also don't require to alter the plan of your previous water pipes.
Your devices and product checklist must consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is commonly the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
    Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the tap in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Setting up the Bathtub


    Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
    The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reads degree.
    To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
    Switch on the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub as well as also examine the overflow outlet as well as the normal outlet for leakages.
    Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized at the very least once as this will settle it right into its last position.

    Preparing for the Setup


    To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
    Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final position.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this activity before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently available on the market. It is suggested to fit the floor tiles using waterproof or water-proof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    Do you enjoy more info about Tools You Need to Install a New Bathtub ? Give a comment down below. We will be glad to find out your suggestions about this entry. Hoping that you visit us again before long. Appreciated our write-up? Please share it. Let others locate it. Thanks for your time. Visit us again soon.




    Article


    Report this page